IEI DOOR GARD KEYPAD MANUAL CODE
IEI DOOR GARD KEYPAD MANUAL FREE

The 250 comes with a power supply and a printer cable and it easily connects to any parallel printer. Up to 8 keypads can be monitored simultaneously. Using the 250 Printer Interface (not included), you can get an accurate real-time audit trail. Please remember to access program mode when auto entry is on, do not press the * key (Press: 99 # master code), however the * is required while entering programming commands. To use this feature, the user codes must be the same length as the master code.

IEI DOOR GARD KEYPAD MANUAL CODE

You only need to enter your code number (without pressing *) and the relay activates.

This feature is used when you don’t want to press the * key after entering your code. This output is not available if you are using the IEI 250 Printer Interface. You can use this to turn on lights, CCTV camera, or notify a guard. You can turn this off through programming.ĭoor♦Gard Command and Control keypads can be programmed to energize a voltage output whenever a key is touched. The auxiliary outputs activate for their programmed time.ĭoor♦Gard Command and Control keypads, by default, acknowledge a keypress by momentarily illuminating the yellow LED or activate the sounder. You can also program the REX to operate any combination of the available outputs. By default, it operates output 4 and activates for 1 second.īy default, upon a momentary closure this normally open loop triggers the main relay for the same time period as the Master Code. Panic is activated by pressing the * and # keys at the same time. Some models have 1 Amp form C relays and other models have negative voltage outputs with a 50mA sink.*

They can be controlled individually or in combination by a code.

You can program these outputs as timed outputs (1 to 90 seconds) or to toggle (latch). See the Wiring Diagram and Specifications for the relay electrical specifications. The main relay is a form C relay, which you can program as a timed output (1 to 90 seconds) or to toggle (latch). The Master Code is always stored in user location one (1). Codes can be 1 to 6 digits in length and digits may be repeated. The Door♦Gard Command and Control keypads allow up to 120 individual user codes. It takes seconds for an authorized user to change codes. LED or sounder guidance makes programming easy. This warranty shall expire two years after shipping date for DOOR-GARD keypads.Įxcept as stated above, IEI makes no warranties, either express or implied, as to any matter whatsoever, including, without limitation to, the condition of its products, their merchantability, or fitness for any particular purpose.Non-volatile EEPROM memory means your codes and instructions will be there whether you remove power for 5 minutes or 5 years.Īll programming is done entirely from the front of the keypad. IEI will not be liable to the purchaser or anyone else for incidental or consequential damages arising from any defect in, or malfunction of, its products. IEI’s sole liability is limited to the repair or (at IEI’s option) the replacement of the defective product or part when sent to IEI’s facility (freight and insurance charges prepaid), after first obtaining IEI’s Return Merchandise Authorization. IEI does not assume any responsibility for damage or injury to person or property due to improper care, storage, handling, abuse, misuse, normal wear and tear, or an act of God.

IEI DOOR GARD KEYPAD MANUAL FREE

(IEI) warrants its products to be free from defects in material and workmanship, when they have been installed in accordance with the manufacturer’s instructions, and have not been modified or tampered with. On SE keypad, holes have also been spotted inside the front housing for additional LEDs (LEDs not included).To speed installation of the SE keypad, holes have been spotted on the inside the back housing for mounting to a wall or a single-gang electrical box.For use in extreme weather conditions, consult the factory for additional methods of protecting your keypad.This allows air to circulate and a place for condensation to drain. Do not seal the drain holes at the bottom of the keypad housing.Do not silicone the cover plate because the unit will not seal properly. This helps prevent water from entering the case and condensing on the circuit board. When mounting this unit outside, apply silicone to the area where the wires enter the case.The bi-color LED provided with the SE keypad illuminates red when the LockRelease relay is de-energized and green when the relay is de-energized.To avoid ESD (Electro-Static Discharge) interfering with the operation of the keypad, ground the housing to earth ground.

Iei door gard keypad manual